- #AMC AUTO MOUSE CLICK TUTORIAL HOW TO#
- #AMC AUTO MOUSE CLICK TUTORIAL FOR MAC OSX#
- #AMC AUTO MOUSE CLICK TUTORIAL MAC OS X#
- #AMC AUTO MOUSE CLICK TUTORIAL MAC OSX#
- #AMC AUTO MOUSE CLICK TUTORIAL PDF#
#AMC AUTO MOUSE CLICK TUTORIAL MAC OS X#
Watch How you can Repeat Action or Script and Utilize this Mac OS X Automation Software to the fullest.You can either use Text to Voice Conversion or Simply use System Sounds as Audible Alerts. Use Audible Alerts to get Notified of Important steps in your Script.This can be handy when you wish to Automate Webforms or Mac OS X Application which require variable Text Input. Automate Text Typing with Data read from File with Type Line Action.
#AMC AUTO MOUSE CLICK TUTORIAL HOW TO#
This Tutorial displays how to Automate Left Click with Macro Script, however the Min Delay and Max Delay can be used for all the Actions in the Script to Randomize the Time Delay before any given Action is Executed.
#AMC AUTO MOUSE CLICK TUTORIAL PDF#
You can also Download a step by step Tutorial as a PDF File.Īnother quick way to learn about this Application is to Download Screenshots and view Various Features offered by this Easy and Advanced Macintosh Automation Application.
#AMC AUTO MOUSE CLICK TUTORIAL MAC OSX#
This Mac OSX Automation Utility allows you to Automate Mouse Clicking, Key Pressing and much more. Given below are few Video Tutorials to get you Started with Auto Mouse Click for Mac.
#AMC AUTO MOUSE CLICK TUTORIAL FOR MAC OSX#
It's a great rig, but as you can see there are currently a few quirks.Video Tutorials for Auto Mouse Click for Mac OSX Tutorials for Auto Mouse Click by
I have also heard that sometimes the RS232 connection causes sd card load problems, the solution being you have to disconnect the RS232 cable from the back of the rig before trying to load files. If you have problems with the rig wanting to update the firmware when you switch on, this is caused by the equipment on the other end of your RS232 connection not being switched on. To test a value of AMC you have to jump back into the same menu setting and select COMP before you can adjust compressor settings to see if you can get it to behave. Most microphones work well at a setting of approx. Starting from 100 work your way down until the you can set the compression and ALC level as stated in the manual. A setting of 100 will give you distorted modulation and cause the compression and mic gain to be impossible to set correctly. Note the value is counter intuitive, a setting of 100 means no AMC limiting, a setting of 1 is maximum AMC limiting. The AMC level can then be adjusted using the Proc rotary control to dial in an AMC value. AMC is on all the time, but you can only control its level by selecting (Operation Setting -> Tx Audio -> Proc Level -> AMC). When setting up the microphone audio and drive levels AMC is mega important.
a setting of 10 means a response over a small bandwidth (say 100Hz) and a setting of 1 means a response over a large bandwidth say (1KHz). When setting up the microphone equaliser bandwidth (Operation Setting -> Tx Audio -> PRMTRC EQx BWTH), bandwidth is a very misleading word, Yaesu actually mean 'Q' i.e. Both the RS232 and the rear USB ports work for CAT control simultaneously. If you want to use the radio with a wireless mouse, all wireless mice are not the same, I finally found that a Logitech M310 works when connected to the top USB port on the front of the radio (it doesn't work in the bottom port).
From then on it will remember you want BK-IN when sending CW from SSB mode. To get CW Auto Mode to work, you have to select CW mode turn on BK-IN then select SSB mode. If you have CW Auto Mode (CW Setting -> MODE CW -> CW AUTO MODE) set to ON, you can still turn your PROCessor on/off using the PROC button, the trick is that you have to engage PTT and then press the PROC button to get it to switch the Proc on/off rather than the Keyer on/off.